Separation operations achieve their objective by the creation of two or more coexisting zones which differ in temperature, pressure, composition, and/or phase state. Each molecular species in the mixture to be separated responds in a unique way to differing environments offered by these zones. Consequently, as the system moves toward equilibrium, each species establishes a different concentration in each zone, and this results in a separation between the species.
The separation operation called distillation utilizes vapor and liquid phases at essentially the same temperature and pressure for the coexisting zones. Various kinds of devices such as random or structured packings and plates or trays are used to bring the two phases into intimate contact. Trays are stacked one above the other and enclosed in a cylindrical shell to form a column. Packings are also generally contained in a cylindrical shell between hold-down and support plates. The column may be operated continuously or in batch mode depending on a number of factors such as scale and flexibility of operations and solids content of feed. A typical tray-type continuous distillation column plus major external accessories is shown
schematically in Fig. below.
The feed material, which is to be separated into fractions, is introduced at one or more points along the column shell. Because of the difference in density between vapor and liquid phases, liquid runs down the column, cascading from tray to tray, while vapor flows up the column, contacting liquid at each tray.
Liquid reaching the bottom of the column is partially vaporized in a heated reboiler to provide boil-up, which is sent back up the column. The remainder of the bottom liquid is withdrawn as bottoms, or bottom product. Vapor reaching the top of the column is cooled and condensed to liquid in the overhead condenser. Part of this liquid is returned to the column as reflux to provide liquid overflow. The remainder of the overhead stream is withdrawn as distillate, or overhead product. In some cases only part of the vapor is condensed so that a vapor distillate can be withdrawn.
This overall flow pattern in a distillation column provides countercurrent contacting of vapor and liquid streams on all the trays through the column. Vapor and liquid phases on a given tray approach thermal, pressure, and composition equilibria to an extent dependent upon the efficiency of the contacting tray.
The lighter (lower-boiling temperature) components tend to concentrate in the vapor phase, while the heavier (higher-boiling temperature)components concentrate in the liquid phase. The result is a vapor phase that becomes richer in light components as it passes up the column and a liquid phase that becomes richer in heavy components
as it cascades downward. The overall separation achieved between the distillate and the bottoms depends primarily on the relative volatilities of the components, the number of contacting trays in each column section, and the ratio of the liquid-phase flow rate to the vapor-phase flow rate in each section.
If the feed is introduced at one point along the column shell, the column is divided into an upper section, which is often called the rectifying section, and a lower section, which is often referred to as the stripping section. In multiple-feed columns and in columns from which a liquid or vapor sidestream is withdrawn, there are more than two column sections between the two end-product streams. The notion of a column section is a useful concept for finding alternative systems (or sequences) of columns for separating multicomponent mixtures, as described below in the subsection Distillation Systems.
All separation operations require energy input in the form of heat or work. In the conventional distillation operation, energy required to separate the species is added in the form of heat to the reboiler at the bottom of the column, where the temperature is highest. Also heat is removed from a condenser at the top of the column, where the temperature is lowest. This frequently results in a large energy-input requirement and low overall thermodynamic efficiency, especially if the heat removed in the condenser is wasted. Complex distillation operations that offer higher thermodynamic efficiency and lower energy-input requirements have been developed and are also discussed below in the subsection Distillation Systems.
Batch distillation is preferred for small feed flows or seasonal production which is carried out intermittently in “batch campaigns.” In this mode the feed is charged to a still which provides vapor to a column where the separation occurs. Vapor leaving the top of the column is condensed to provide liquid reflux back to the column as well as a distillate stream containing the product. Under normal operation, this is the only stream leaving the device. In addition to the batch rectifier just described, other batch configurations are possible as discussed in the subsection Batch Distillation. Many of the concepts and methods discussed for continuous distillation are useful for developing models and design methods for batch distillation.
Schematic diagram and nomenclature for a simple continuous distillation column with one feed, a total overhead condenser, and a partial reboiler.